manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 339

9-47

Confidential

9.4.25 Purge Operation 

(Function code 76)

 

(User-accessible)

„

Function

The machine can carry out several types of purge operations--head replacement purge, normal
purge, periodical reset purge, power purge, initial purge, user reset purge, and engine setup
purge. This function allows you to select the desired purge type and carry it out.

TIP: 

The purge types and their details are described on the next page.

„

Operating Procedure

(1) Press the 

7

 and 

6

 keys in this order in the initial stage of the maintenance mode.

The machine displays the "CLEANING ALL" on the LCD and enters the purge mode.

(2) Press the   or   key to display the target color for purge.

Each time the   or   key is pressed, the "CLEANING ALL," "CLEANING BLACK,"
"CLEANING MAGENTA," "CLEANING CYAN," or "CLEANING YELLOW" appears
cyclically.

"CLEANING ALL": Purge for all four color inks

"CLEANING BLACK": Purge for black ink

"CLEANING MAGENTA" / "CLEANING CYAN" / "CLEANING YELLOW": Any color 
choice performs purge for all three color inks.

(3) Enter the purge code according to the table on the next page.

(4) Press the 

Black Start 

(

Mono Start

) key.

Upon completion of purging, the machine automatically returns to the initial stage of the
maintenance mode.

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands