manualshive.com logo in svg

Brother HL-960 Series, User Manual

The Brother HL-960 Series is a versatile printing solution designed for small offices and homes. With its user-friendly features, this reliable printer ensures high-quality prints every time. Access the detailed User Manual for this product, available for free download on our website, to maximize its capabilities and functionality.

Share
Download
background image

USER’S GUIDE

7–10

■

Paper Jam at the Paper Access Cover Inside the Printer

13 JAM INSIDE

If a paper jam occurs at the paper access cover, follow these steps to
remove the jammed paper:

1. Pull  the upper paper cassette out of the printer to release the edge of

the paper from the paper feed roller, or the paper might be torn and
difficult to  remove.

2. Open the top cover and remove the toner cartridge.

3. Raise the paper access cover.

4. Remove the jammed paper using the following methods:

If paper has passed through the paper access cover and toner is on
the paper, pull it with making paper edge round in direction A
(toward the upper side of the printer).

☛

Caution

Take care not to stain your hands and clothes with toner. Wash out toner
stains immediately with cold water.

Fig. 7-5  Paper Jam at Paper Access Cover

5. Close the paper access cover.

6. Install the toner cartridge and close the top cover.

Paper Access
Cover

Direction A

Summary of Contents for HL-960 Series









































































































































































































































































Reviews:

No comments

Related manuals for HL-960 Series

CAB A Series Programming Manual preview
A Series
Brand: CAB Pages: 263
Oki B2200 Specifications preview
B2200
Brand: Oki Pages: 2
Datecs PP-55 User Manual preview
PP-55
Brand: Datecs Pages: 73
Datamax H-Class Quick Start Manual preview
H-Class
Brand: Datamax Pages: 12
Datamax E-Class Mark II Maintenance Manual preview
E-Class Mark II
Brand: Datamax Pages: 40
Datamax E-class E-3202 Quick Reference Manual preview
E-class E-3202
Brand: Datamax Pages: 46
Canon PIXMA TR4500 Series Getting Started preview
PIXMA TR4500 Series
Brand: Canon Pages: 100
QuickLabel Systems QL800 User Manual preview
QL800
Brand: QuickLabel Systems Pages: 122
Lexmark 34A0252 Troubleshooting Manual preview
34A0252
Brand: Lexmark Pages: 9
Oki C7500n Maintenance Manual preview
C7500n
Brand: Oki Pages: 192
3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print... User Manual preview
3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...
Brand: 3Com Pages: 94
Olympus U-5RES-ESD Instructions Manual preview
U-5RES-ESD
Brand: Olympus Pages: 16
Lexmark 5470 - X Color Inkjet User Manual preview
5470 - X Color Inkjet
Brand: Lexmark Pages: 202
Jolimark NP311D Instruction Manual preview
NP311D
Brand: Jolimark Pages: 31
iDPRT SP410 User Manual preview
SP410
Brand: iDPRT Pages: 41
Ricoh SP C222DN Administration Manual preview
SP C222DN
Brand: Ricoh Pages: 284
Olivetti PR4 SLIP Service Manual preview
PR4 SLIP
Brand: Olivetti Pages: 56
Kyocera ECOSYS M3860idn Operation Manual preview
ECOSYS M3860idn
Brand: Kyocera Pages: 483

Brands by name

Popular brands

Load more brands