Brother HL-960 Series User Manual Download Page 132 | Manualshive

Page: 132 / 264

background image

USER’S GUIDE

4–64

ECONOMY Switch

POWER SAVE MODE

You can turn on or off the power save mode as follows:

Display Message

Power Save Mode

POWER SAVE=ON

Turn on the power save mode. The fixing
assembly of the print engine is turned off
after the specified time to save power.

(Factory setting)

POWER SAVE=OFF

Turn off the power save mode. The fixing
assembly of the print engine is always
powered on to keep its temperature at the
specified level.

When you turn on the power save mode with the SET switch, the
display shows the next sub-setting menu as follows:

TIME OUT=30m *

You need to set the time out for the power save mode from 1 to 99
minutes with the

▲

or

▼

switch:

factory setting =30 minutes

. The

time out is the duration after which the fixing assembly of the print
engine is turned off (“SLEEP”) to save power.

When the power save mode is turned on, the printer turns on the
fixing assembly again after it receives data from the computer. Since
the fixing assembly must reach the specified high temperature, it
takes a little longer time to start printing the first page.

«
...
130
131
132
133
134
...
»

Summary of Contents for HL-960 Series









































































































































































































































































Reviews:

No comments

Related manuals for HL-960 Series

Brand: Olivetti Pages: 39

Brand: Labau Pages: 19

Brand: Datecs Pages: 29

Brand: TallyGenicom Pages: 3

Brand: Olivetti Pages: 20

Brand: Olivetti Pages: 63

Brand: Olivetti Pages: 180

Brand: Olivetti Pages: 118

Brand: Olivetti Pages: 80

Brand: Olivetti Pages: 253

Brand: Olivetti Pages: 163

d-COLOR MF222plus

Brand: Olivetti Pages: 151

Brand: Olivetti Pages: 176

Brand: Raymarine Pages: 135

Accel-a-Writer 8300

Brand: Xante Pages: 12

3635MFP - Phaser B/W Laser

Brand: Xerox Pages: 16

Brand: Xerox Pages: 262

Brand: Konica Minolta Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands