manualshive.com logo in svg

Brother HL-960 Series, User Manual

The Brother HL-960 Series is a versatile printing solution designed for small offices and homes. With its user-friendly features, this reliable printer ensures high-quality prints every time. Access the detailed User Manual for this product, available for free download on our website, to maximize its capabilities and functionality.

Share
Download
background image

CHAPTER 2 GETTING STARTED

2–7

Installing the Toner Cartridge

This printer uses a toner cartridge to print. You have one toner cartridge
as standard. A new cartridge contains enough toner to print
approximately 6,000 A4 or letter-size single-sided pages at about 5%
coverage (if the print density is set at level 8).

If you turn on the printer without the toner cartridge installed, the
display shows the following operator call message to prompt you to
install the toner cartridge.

14 NO CARTRIDGE

To install the toner cartridge, follow these steps:

1. Open the top cover of the printer.

2. Open the bag to unpack the toner cartridge.

☛

  Caution

 • 

Do not expose the toner cartridge to direct light.

 • 

Do not stand the toner cartridge on its end or turn it up-side down.

 • 

Do not touch the shaded parts shown below.

 • 

Do not open the drum shutter otherwise the toner or drum is
adversely affected and might cause serious damage when printing.

Fig. 2-9  Don’ts When Handling the Toner Cartridge

Drum Shutter

Summary of Contents for HL-960 Series









































































































































































































































































Reviews:

No comments

Related manuals for HL-960 Series

Canon 1750 Service Manual preview
1750
Brand: Canon Pages: 358
Oki C5800 Brochure & Specs preview
C5800
Brand: Oki Pages: 6
Oki C7300 Référence Matérielle preview
C7300
Brand: Oki Pages: 44
Oki C7500 Enhancements Manual preview
C7500
Brand: Oki Pages: 13
Oki C7300 Software Installation Manual preview
C7300
Brand: Oki Pages: 20
Oki C7300 Specifications preview
C7300
Brand: Oki Pages: 2
Oki C5300 Setup Manual preview
C5300
Brand: Oki Pages: 28
Xerox B310 User Manual preview
B310
Brand: Xerox Pages: 192
Canon RP10 User Manual preview
RP10
Brand: Canon Pages: 37
Samsung CLX-6260ND User Manual preview
CLX-6260ND
Brand: Samsung Pages: 368
Citizen CBM1000II RF User Manual preview
CBM1000II RF
Brand: Citizen Pages: 133
Printek DP-530si Operator'S Manual preview
DP-530si
Brand: Printek Pages: 34
Oce VarioPrint 6180 User Manual preview
VarioPrint 6180
Brand: Oce Pages: 306
Olympus 201021 - P 330N Photo Printer Installation Manual preview
201021 - P 330N Photo Printer
Brand: Olympus Pages: 79
Fuji Xerox DocumentCentre C240 Series User Manual preview
DocumentCentre C240 Series
Brand: Fuji Xerox Pages: 275
TonerRefillKits ReChargX RX180 Instructions Manual preview
ReChargX RX180
Brand: TonerRefillKits Pages: 10
Triumph Adler 5057i Quick Manual preview
5057i
Brand: Triumph Adler Pages: 4
SPRT SP-POS5810 User Manual preview
SP-POS5810
Brand: SPRT Pages: 12

Brands by name

Popular brands

Load more brands