Brocade Communications Systems Fabric OS v7.0.1 Command Reference Manual Download Page 722

Page: 722 / 1132

696

Fabric OS Command Reference

53-1001764-01

portCfgShow

TPerf Option: Off

IPSec: Enabled (legacy)

IPSec Key: '12345678901234567890123456789012'

QoS Percentages: High 50%, Med 30%, Low 20%

Remote WWN: Not Configured

Local WWN: 10:00:00:05:1e:52:fe:00

Flags: 0x00000000

FICON: Off

switch:admin>

portcfgshow fciptunnel 1/12

-------------------------------------------

Tunnel ID: 1/12

Tunnel Description:

Compression: Off

Fastwrite: Off

Tape Acceleration: Off

TPerf Option: Off

IPSec: Enabled (legacy)

QoS Percentages: High 50%, Med 30%, Low 20%

Remote WWN: Not Configured

Local WWN: 10:00:00:05:1e:52:fe:00

Flags: 0x00000000

FICON: Off

To display the inband management interface for a single GbE Port on a Brocade 7800:

switch:admin>

portcfgshow mgmtif ge0

Inband Management: ge0 Enabled

Interface IPv4 Address NetMask Effective MTU Flags

--------------------------------------------------------------

0 20.20.0.151 255.255.255.0 1500

Flags: U=Up B=Broadcast D=Debug L=Loopback P=Point2Point R=Running

N=NoArp PR=Promisc M=Multicast S=StaticArp LU=LinkUp

To display the management route for a configured inband management interface on a Brocade 7800:

switch:admin> portcfgshow mgmtroute ge0

Port: ge0

IP Address Mask Gateway Metric Flags

-------------------------------------------------------------

192.168.1.0 255.255.255.0 20.20.1.250 0

Flags: U=Usable G=Gateway H=Host C=Created(Interface) S=Static

L=LinkLayer(Arp)

Summary of Contents for Fabric OS v7.0.1













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Fabric OS v7.0.1

Reviews:

Related manuals for Fabric OS v7.0.1

Brands by name

Popular brands

Brocade Communications Systems Fabric OS v7.0.1, Command Reference Manual

Search results

Summary of Contents for Fabric OS v7.0.1

Reviews:

Related manuals for Fabric OS v7.0.1

Brands by name

Popular brands