manualshive.com logo in svg

Brocade Communications Systems Brocade 8/12c, Command Reference Manual

The Brocade Communications Systems Brocade 8/12c is a cutting-edge networking solution renowned for its robust performance and reliability. To easily set up and configure this product, ensure seamless installation by accessing the comprehensive Installation Manual available for free download at our website.

Share
Download
background image

Fabric OS Command Reference

121

53-1001764-01

cmsh

22

cmsh

Opens the CEE command shell. 

SYNOPSIS

cmsh

DESCRIPTION

Use this command to open a shell for managing 10 GbE interfaces and Layer2/Layer3 protocol services. 
The CEE management shell provides a hierarchical CLI interface. 

Refer to the 

CEE Command Reference

 and the 

CEE Administrator's Guide

 for information on how to use 

the CEE commands and configuration procedures.

NOTES

The execution of this command is subject to Virtual Fabric or Admin Domain restrictions that may be in 
place. Refer to Chapter 1, "Using Fabric OS Commands" and Appendix A, "Command Availability" for 
details.

OPERANDS

None

EXAMPLES

To run FCoE using the minimum switch configuration:

switch:admin> 

cmsh

admin>en

admin>#conf t

Enter configuration commands, one per line. End with CNTL/Z.

admin>(config)#int te 0/0

admin>(config-if)#sw

admin>(config-if)#no shut

admin>(config-if)#exit

admin>(config)#exit

admin>#show ip int br

Interface IP-Address Status Protocol

TenGigabitEthernet 0/0 unassigned up up

TenGigabitEthernet 0/1 unassigned administratively down down

TenGigabitEthernet 0/2 unassigned administratively down down

TenGigabitEthernet 0/3 unassigned administratively down down

TenGigabitEthernet 0/4 unassigned administratively down down

TenGigabitEthernet 0/5 unassigned administratively down down

TenGigabitEthernet 0/6 unassigned administratively down down

TenGigabitEthernet 0/7 unassigned administratively down down

TenGigabitEthernet 0/8 unassigned administratively down down

TenGigabitEthernet 0/9 unassigned administratively down down

TenGigabitEthernet 0/10 unassigned administratively down down

TenGigabitEthernet 0/11 unassigned administratively down down

TenGigabitEthernet 0/12 unassigned administratively down down

TenGigabitEthernet 0/13 unassigned administratively down down

TenGigabitEthernet 0/14 unassigned administratively down down

TenGigabitEthernet 0/15 unassigned administratively down down

TenGigabitEthernet 0/16 unassigned administratively down down

TenGigabitEthernet 0/17 unassigned administratively down down

TenGigabitEthernet 0/18 unassigned administratively down down

TenGigabitEthernet 0/19 unassigned administratively down down

TenGigabitEthernet 0/20 unassigned administratively down down

TenGigabitEthernet 0/21 unassigned administratively down down

TenGigabitEthernet 0/22 unassigned administratively down down

TenGigabitEthernet 0/23 unassigned administratively down down

switch:admin>#exit

Summary of Contents for Brocade 8/12c













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Brocade 8/12c

F-SECURE PSB Administrator'S Manual preview
PSB
Brand: F-SECURE Pages: 43
Garmin GNC 420 Instructions Manual preview
GNC 420
Brand: Garmin Pages: 6
Adobe 718659340025 - InDesign CS - PC Printing Manual preview
718659340025 - InDesign CS - PC
Brand: Adobe Pages: 122
Symantec 20032623 - Endpoint Protection Small Business Edition Implementation Manual preview
20032623 - Endpoint Protection Small Business Edition
Brand: Symantec Pages: 351
VMware VCENTER CHARGEBACK 1.5 - API Manual preview
VCENTER CHARGEBACK 1.5 - API
Brand: VMware Pages: 150
Xerox 701P40211 System Manual preview
701P40211
Brand: Xerox Pages: 110
Aastra MX-ONE 4.2 User Manual preview
MX-ONE 4.2
Brand: Aastra Pages: 46
Honeywell Dolphin 7200 Software Manual preview
Dolphin 7200
Brand: Honeywell Pages: 2
Honeywell INTEGRA User Manual preview
INTEGRA
Brand: Honeywell Pages: 14
Honeywell 7850LP-I1-5210E - Hand Held Products Dolphin 7850 User Manual preview
7850LP-I1-5210E - Hand Held Products Dolphin 7850
Brand: Honeywell Pages: 36
Honeywell Dolphin Demos User Manual preview
Dolphin Demos
Brand: Honeywell Pages: 46
Honeywell RAPID EYE MULTI-MEDIA Operator'S Manual preview
RAPID EYE MULTI-MEDIA
Brand: Honeywell Pages: 144
Honeywell ARENA User Manual preview
ARENA
Brand: Honeywell Pages: 160
Honeywell WebVision User Manual preview
WebVision
Brand: Honeywell Pages: 176
Honeywell Dolphin Power Tools User Manual preview
Dolphin Power Tools
Brand: Honeywell Pages: 176
ArcSoft DV-6400 Quick Start Manual preview
DV-6400
Brand: ArcSoft Pages: 6
GameShark GAME CUBE Instruction Manual preview
GAME CUBE
Brand: GameShark Pages: 16
LEI Extras MAPCREATE 7 - ADDENDUM Quick Start Manual preview
MAPCREATE 7 - ADDENDUM
Brand: LEI Extras Pages: 16

Brands by name

Popular brands

Load more brands