8
86
NOTE:
Exercise care to avoid dropping screw
between engine and blower housing. A dropped
screw may be caught by the flywheel magnet where
disassembly would be required to retrieve it.
14. On opposite side, install two hex flange nuts (
I
) onto
fuel tank studs. Alternately tighten nuts to
90-110 lb-
in
(10.2-12.4 N-m).
15. Manually exercise governor lever. Verify that
governor lever, link, and springs move freely without
binding, sticking, or contacting fuel tank.
Engine Cover
NOTE:
Install engine cover if equipped with remote fuel
tank.
1. See Figure 127. Install hose (
A
) in engine cover (
B
)
routing it through either the top or side cutout (
C
).
2. Install fuel hose with clamp (
D
) onto carburetor fuel
inlet fitting. Squeeze tangs and move hose clamp
about
1/8 inch
(3 mm) from end of hose with tangs
pointing upward for best access.
3. Start two screws (
E
) with hex nuts (
F
) to fasten
engine cover to crankcase flanges (dipstick side).
4. Start screw (
G
) to fasten engine cover to crankcase
flange (spark plug side).
5. Alternately tighten screw and hex nuts to
40-60 lb-in
(4.5-6.8 N-m).
127
Starter Motor/Regulator (If Equipped)
1. See Figure 128. Install two locating pins (
A
) into
threaded holes in crankcase.
2. With the stator wires routed over the top of the starter
motor, install starter motor (
B
) onto locating pins.
3. Install top starter motor screw (
C
) and tighten to
80-110 lb-in
(9-12.4 N-m).
4. See Figure 129. Install flywheel guard (
D
), so that
lower mounting hole is positioned between the blower
housing and boss in engine base.
5. Loosely install bottom blower housing screw (
E
) into
engine base capturing flywheel guard.
6. Rotate flywheel guard until the top hole contacts the
lower starter mounting foot.
7. Loosely install bottom starter motor screw (
F
) into
crankcase capturing flywheel guard.
8. Install side blower housing screw (
G
) and tighten to
80-110 lb-in
(9-12.4 N-m).
9. Tighten bottom blower housing screw to
80-110 lb-in
(9-12.4 N-m).
10. Tighten bottom starter motor screw to
80-110 lb-in
(9-12.4 N-m).
11. If equipped, install low oil sensor module as follows:
A. Install hex flange screw (
H
) to fasten oil sensor
module bracket to flywheel guard. Tighten screw
to
80-110 lb-in
(9-12.4 N-m).
B. Connect one-place wire connector between
armature and oil sensor module.
128
Not for
Reproduction
Summary of Contents for Vanguard 10V300
