background image

9.2 Warranty

This product left the factory in a good working condition in accordance with the technical specifica

-

tions and carries a warranty of 3 years on parts valid from the date of delivery from Braillo Norway 

A/S. 

The warranty includes:

- Replacement of defect part(s)

- Shipping cost for the replaced part(s)

 

The warranty excludes:

- On-site part replacement (labour, travelling and living expenses for a service engineer)

- Shipping costs for sending the faulty unit back to Braillo Norway A/S (see below).

- Altered product (except as authorized by Braillo Norway A/S) or product not installed or maintained 

in accordance with Braillo Norway’s instructions.

- Customs and duties

- Incidents involving Force Major (for example flooding, earth quake etc. damaging the product).

Should a replacement part be required, please do the following:

Send us a “Warranty request form”. Please refer to the next page to see the actual form. The form can 

also be found on the enclosed CD-ROM. After completing the form, please return it to Braillo Norway 

A/S by e-mail, fax or regular mail. When received, the parts will be shipped as soon as possible.

What to do with the defective part(s):

If a communication has been made to our service department, and an approval has been given, it will 

not be necessary to return the part(s) to Braillo Norway A/S. In all other cases, the part(s) must be 

returned to Braillo Norway A/S as soon as possible. If the part(s) has/have not been received by Braillo 

Norway A/S within 2 months from the date of issuing the “Warranty request form”, this is no longer 

regarded as a warranty matter and an invoice will be issued and sent.

BRAILLO

 

l

B 600 SR

116

Summary of Contents for 600 SR
























































































































Reviews: