Braillo 600 SR User Manual Download Page 75

Page: 75 / 119

BRAILLO

B 600 SR

4.14 Eccentrics adjustment, belt tension

After removing the belt, it is necessary to align the eccentrics.

Put the belt back on, tighten it with the belt tensioner (2), and check that the arrows at the end of the

shafts (1) are pointing towards each other. See figure below.

If the marks are not aligned like in the figure, it might be necessary to move the belt a notch or two on

one of the wheels. This is done by loosening the belt tensioner (2) again, and then lift the belt up from

the big wheel and move it a notch on the wheel. Then thighten the belt.

Hold away

from belt

When pushing in by hand,

the distance should be

approx. 10 - 15 mm.

The belt tension is controlled/adjusted like

this:

Remove the flexible tensioner from the belt.

Now the fixed tensioner (2) should be adjusted

so it is possible to press the belt inwards about

10 - 15 mm. Then adjust the flexible tensioner

so the belt runs without vibration.

Summary of Contents for 600 SR
























































































































Search results

Summary of Contents for 600 SR

Reviews:

Related manuals for 600 SR

Brands by name

Popular brands

Braillo 600 SR, User Manual

Search results

Summary of Contents for 600 SR

Reviews:

Related manuals for 600 SR

Brands by name

Popular brands