Brady BMP71 User Manual Download Page 79 | Manualshive

Page: 79 / 147

background image

Barcode

Barcode Settings

68

BMP71 User’s Manual

Barcode

Barcode data can be displayed in the same line as other data (text or symbols). It is not
necessary to have a separate area for the barcode. Barcode data on the same line as text will
not overwrite the text already on the line but will be placed next to it. The height of the
barcode is detemrined in the Barcode Setup function. (See “Setup Barcode” on

page 29

for

more information.) Any text in the same line as the barcode will align on the baseline with the
barcode.

Barcode Settings

Field

To Use

Barcode Symbology

The BMP71 Label Printer supports Code 128 and Code

139 barcode symbology.

Ratio

The ratios available are 2:1 and 3:1.

Height

The height of the bars in a barcode can vary, with a

minimum of 0.1 inch (2.54 mm).

Width

The width of the narrow bar of a barcode is 1, 2, or 3 dots.

Human Readable

Human Readable text can be placed above or below the barcode, or
you can choose to not have it displayed.

Check Digit

A check digit is used for error detection in a barcode. You can turn
the check digit function on or off.

«
...
77
78
79
80
81
...
»

Summary of Contents for BMP71




















































































































































Reviews:

No comments

Related manuals for BMP71

Brand: TEFAL Pages: 76

Brand: G3 Ferrari Pages: 18

Brand: UFESA Pages: 48

Brand: Melissa Pages: 1

Brand: U-Line Pages: 2

Brand: Kalorik Pages: 24

Brand: Havso Pages: 20

Brand: Krups Pages: 33

Dual Brew Pro CFP300

Brand: Ninja Pages: 15

VIVA PRESTIGE RI84 Series

Brand: Gaggia Milano Pages: 156

Brand: Faema Pages: 148

Brand: Bialetti Pages: 116

Brand: nedis Pages: 32

Duraflex 150-8 Valve

Brand: Cornelius Pages: 19

Brand: Buffalo Pages: 56

Brand: Canon Pages: 33

Brand: Ice-O-Matic Pages: 13

Brand: Sapphire Audio Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands