Brady BMP71 User Manual Download Page 14

Page: 14 / 147

Introduction

Physical and Environmental Characteristics

BMP71 User’s Manual

BMP71 System Specifications

The BMP71 printer has the following specifications:

• Weight 5.45 lbs

(2.47 kg) (with battery, no consumables)

• Thermal Transfer Print Mechanism 300 dpi

• Optical Registration System for Precise Print Registration

• Elastomeric Keypad

• 3.5” QVGA color LCD

• Custom True Type Fonts

• Print Width - 51 mm, 2” maximum label width

• Maximum print length for labels: 40” (1016 mm)

• Prints up to 3900 1” x 2” labels per battery charge

Physical and Environmental Characteristics

The BMP71 printer has the followng physical and environmental characteristics:

Note

The table below refers to the BMP71 printer only. Consumable performance may
vary.

Physical

Metric Units

U.S. Units

Dimensions

330 x 241x 117 mm

13.0” L x 9.5” Wx 4.6” H.

Weight (with battery pack)

2.5 kg

5.5 lb.

Summary of Contents for BMP71




















































































































































Search results

Summary of Contents for BMP71

Reviews:

Related manuals for BMP71

Brands by name

Popular brands

Brady BMP71, User Manual

Search results

Summary of Contents for BMP71

Reviews:

Related manuals for BMP71

Brands by name

Popular brands