Bosch VIP-X1XF Installation And Operating Manual Download Page 61

Page: 61 / 132

VIP X1 XF

Configuration using a Web browser | en

Bosch Sicherheitssysteme GmbH

Installation and Operating Manual

DOC | V4.54 | 2011.09

Certain details on the recording status are displayed here for information purposes. You

cannot change any of these settings.

5.27

Advanced Mode: Alarm Connections

You can select how the VIP X1 XF responds to an alarm. In the event of an alarm, the unit can

automatically connect to a pre-defined IP address. You can enter up to ten IP addresses to

which the VIP X1 XF will connect in sequence in the event of an alarm, until a connection is

made.

Connect on alarm

Select

so that the VIP X1 XF automatically connects to a predefined IP address in the event

of an alarm.

By setting

Follows input 1

the unit maintains the connection that has been automatically

established for as long as an alarm exists on alarm input 1.

Number of destination IP address

Specify the numbers of the IP addresses to be contacted in the event of an alarm. The unit

contacts the remote stations one after the other in the numbered sequence until a connection

is made.

Destination IP address

For each number, enter the corresponding IP address for the desired remote station.

Destination password

If the remote station is password protected, enter the password here.

NOTICE!

In the default setting, Stream 1 is transmitted for alarm connections. Bear this fact in mind

when assigning the profile (see

Section 5.19 Advanced Mode: Encoder Profile, page 47

Summary of Contents for VIP-X1XF





































































































































Search results

Summary of Contents for VIP-X1XF

Reviews:

Related manuals for VIP-X1XF

Brands by name

Popular brands

Bosch VIP-X1XF, Installation And Operating Manual

Search results

Summary of Contents for VIP-X1XF

Reviews:

Related manuals for VIP-X1XF

Brands by name

Popular brands