Bosch rexroth SB24 Instruction Manual Download Page 55

Page: 55 / 78

Installation 55/78

RE 66170-B/2019-05-15, Control block SB24/34, Bosch Rexroth AG

7 Installation

Prior to installation, the following documents should be to hand:

• Offer drawing (installation drawing) of the control block/control block segment

(can be obtained from your contact at Bosch Rexroth)

• Hydraulic circuit diagram of the control block/control block segment

(can be found in the offer drawing)

• Hydraulic circuit diagram of the machine (available from the machine/system

manufacturer)

• Data sheet of the control block/control block segment (contains permissible

technical data)

7.1 Unpacking

CAUTION!

Danger due to falling parts!

If the packaging is not opened correctly, parts may fall out and damage the parts or
even result in injury.

▶

Place the packaging on a level surface with sufficient load-bearing capacity.

Remove any packaging from the product.

Check the control block/control block segment for transport damage and
completeness, see chapter 4 "Scope of delivery" on page 17.

Dispose of the packaging in accordance with the regulations in your country.

Return any reusable packaging to Bosch Rexroth.

7.2 Assembly of control block segments to form a control block

Assembly of directional valve discs and plates to form a control block is described
in the related documentation 66170-10-R.

7.3 Painting the control block/control block segment

For painting of the control block/control block segment before assembly, proceed
as follows:

▶

Apply protective plastic plugs at the hydraulic ports for protection against ingress
of paints.

▶

Screws have to be inserted into the mounting threads to prevent ingress of paint.

▶

Protect flange surfaces of control blocks/control block segments against paint.

▶

Prevent any paint being applied to the contacts of the electrical connections and
make sure that the connectors are not damaged.

▶

When removing the protective plastic plugs after painting, make sure that no
paint chips enter the control block/control block segment.

▶

Protect name plates against application of paint using a film that can be peeled
off after painting.

Summary of Contents for rexroth SB24















































































Search results

Summary of Contents for rexroth SB24

Reviews:

Related manuals for rexroth SB24

Brands by name

Popular brands

Bosch rexroth SB24, Instruction Manual

Search results

Summary of Contents for rexroth SB24

Reviews:

Related manuals for rexroth SB24

Brands by name

Popular brands