Bosch rexroth HQ 2/U-H Assembly Instructions Manual Download

Page: 17 / 72

7 Assembly

7.1

Unpacking



Lift the product out of its packaging.



Dispose of the packaging material in accordance with the applicable regulations

in your country.

7.2

Installation requirements



During installation, be sure to maintain the ambient conditions speciﬁ ed in the

Technical Data (see page 64).

7.2.1 Installation

position



Install the product level and plumb, at right angles, and axially parallel.

This ensures proper functioning and prevents premature wear.

7.3 Required

tools

• Hex wrench (open-end) SW13.

• Hex socket wrenches SW3, SW4, SW5.

• Hex socket wrench (Torx™) T30, T50

• Posidriv screwdriver, PZ2

• Hammer

• Level

• Combination pliers

• Flat smooth ﬁ le

Assembly 17/72

3 842 562 241/2019-04, MIT: HQ 2/U-H,

Bosch Rexroth AG

GLISH

Summary of Contents for rexroth HQ 2/U-H









































































Search results

Summary of Contents for rexroth HQ 2/U-H

Reviews:

Related manuals for rexroth HQ 2/U-H

Brands by name

Popular brands

Bosch rexroth HQ 2/U-H, Assembly Instructions Manual

Search results

Summary of Contents for rexroth HQ 2/U-H

Reviews:

Related manuals for rexroth HQ 2/U-H

Brands by name

Popular brands