Bosch rexroth HQ 2/U-H Assembly Instructions Manual Download

Page: 53 / 72

10.4.2 Replacing the roller chain

Fig. 40:

1,3

1,6

~10

= 22 Nm

SW13

562 240-25

Replacing the roller chain

It is possible to replace

the roller chain when the

HQ 2/U-H is installed in the

section.

Open the chain lock (A).

Replace the roller chain.

Check the sprocket and

the chain guides for

break-in scoring.

Replace the worn parts.

Check the tension of the

roller chain. Adjust the

roller chain tension if

necessary.

Please note:

• Do not pre-tension the

roller chain, the chain

should be able to be

pressed in by ~10 mm.

• Incorrect roller chain

tensioning reduces the

service life of the roller

chain, gear and motor!

Adjusting the roller chain

tension

• Loosen the screws (B)

and move the motor-gear

combination until the

correct chain tension is

achieved.

• Fix this setting with the

screws (B).

Maintenance and repair

53/72

3 842 562 241/2019-04, MIT: HQ 2/U-H,

Bosch Rexroth AG

GLISH

Summary of Contents for rexroth HQ 2/U-H









































































Search results

Summary of Contents for rexroth HQ 2/U-H

Reviews:

Related manuals for rexroth HQ 2/U-H

Brands by name

Popular brands

Bosch rexroth HQ 2/U-H, Assembly Instructions Manual

Search results

Summary of Contents for rexroth HQ 2/U-H

Reviews:

Related manuals for rexroth HQ 2/U-H

Brands by name

Popular brands