Bosch Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 6

Page: 6 / 64

Key to symbols and safety instructions

Logamatic EMS – 6 720 801 387 (2011/05)

1.2

Safety instructions

Installation and commissioning

Observe these instructions to ensure satisfactory operation.

The appliance must only be installed and commissioned by an authorised installer.

Risk of death from electric shock

The power supply must be connected by a qualified electrician.

Observe the connection diagram.

Before installation: isolate all poles of the power supply (230 V AC). Secure against unintentional
reconnection.

Never install this appliance in wet rooms.

Never connect this appliance to the 230 V mains.

Damage through operator error

Operator errors can lead to injuries and/or material losses.

Ensure that children never operate this appliance unsupervised or play with it.

Ensure that only individuals who can operate this appliance correctly have access to it.

Warning: frost

The heating system can freeze up in cold weather if it is not in operation:

Leave the heating system permanently switched on.

Enable frost protection.

In case of faults: remedy any faults immediately.

Summary of Contents for Logamatic EMS RC35

































































Search results

Summary of Contents for Logamatic EMS RC35

Reviews:

Related manuals for Logamatic EMS RC35

Brands by name

Popular brands

Bosch Logamatic EMS RC35, Installation And Service Instructions Manual

Search results

Summary of Contents for Logamatic EMS RC35

Reviews:

Related manuals for Logamatic EMS RC35

Brands by name

Popular brands