Bosch Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 17

Page: 17 / 64

Logamatic EMS – 6 720 801 387 (2011/05)

Principles of operation

4.2

Introduction to the service menu

You can use the

SERVICE MENU

to set the parameters for the system. It also contains functions

for diagnosis, maintenance purposes, and carrying out a reset. The procedure for operation is
always the same:

1. Open the flap (by pulling the recessed grip on the left).

2. Press

simultaneously to open the

SERVICE MENU

3. Turn the

rotary selector to change the selection.

4. Press

to make your selection.

5. To change the value, hold down the

button (the value starts flashing) and turn the rotary

selector

at the same time. Release the

button.

The modified value is saved.

6. Press the

button to go back one step.

Press the

button several times or close the flap to show the standard display again.

Example:

Setting the

building type

(adjusted time)

Operation

Result

Open the flap (by pulling the recessed grip on the left).

Press

simultaneously,

to open the

SERVICE MENU

Turn the

rotary selector to the left until

settings

selected.
Press the

button to confirm the selection.

The

SERVICE\SETTINGS

menu is opened.

Turn the

rotary selector to the left until

boiler data

selected.

Table 5

How to use the service menu (example)

6° 02.12.2005 10:20h
Temp. Exterior -1°C

21.5°C

SERVICE MENU

quick operation
settings
diagnosis
servicing

SERVICE MENU

quick operation
settings
diagnosis
servicing

SERVICE\SETTINGS

plant data
boiler data
domestic hot water
heating circuit 1

Summary of Contents for Logamatic EMS RC35

































































Search results

Summary of Contents for Logamatic EMS RC35

Reviews:

Related manuals for Logamatic EMS RC35

Brands by name

Popular brands

Bosch Logamatic EMS RC35, Installation And Service Instructions Manual

Search results

Summary of Contents for Logamatic EMS RC35

Reviews:

Related manuals for Logamatic EMS RC35

Brands by name

Popular brands