Bosch Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 18

Page: 18 / 64

Principles of operation

Logamatic EMS – 6 720 801 387 (2011/05)

Press

to select

boiler data

The menu

SETTINGS\BOILER

is opened.

To change the value, hold down the

button (the value

starts flashing) and turn the rotary selector

at the same

time.

Release the

button.

The value stops flashing. The modified value is saved.

If you have carried out this example as practice only, make
sure that the original setting is retained.

To do so, repeat steps 6 and 7 if necessary.

Press

to go back one step.

-or-

To finish entering the settings: press

several times or

shut the flap.

The standard display reappears.

You can enter all settings in the SERVICE MENU using this procedure.

Operation

Result

Table 5

How to use the service menu (example)

SETTINGS\BOILER
What type of building

do you have?

medium

SETTINGS\BOILER
What type of building
do you have?

medium

SETTINGS\BOILER
What type of building
do you have?

light

SETTINGS\BOILER
What type of building

do you have?

medium

Summary of Contents for Logamatic EMS RC35

































































Search results

Summary of Contents for Logamatic EMS RC35

Reviews:

Related manuals for Logamatic EMS RC35

Brands by name

Popular brands

Bosch Logamatic EMS RC35, Installation And Service Instructions Manual

Search results

Summary of Contents for Logamatic EMS RC35

Reviews:

Related manuals for Logamatic EMS RC35

Brands by name

Popular brands