Bosch FPA-1200-MPC-C User Manual Download Page 19

Page: 19 / 100

Panel Controller

In overview | en

Bosch Sicherheitssysteme GmbH

User Guide

2017.09 | 7.0 | F.01U.258.929

In overview

This chapter contains information about the following elements of the panel controller:
–

Operating elements, page 19

–

Display elements, page 20

–

Touch screen, page 21

–

Display support information, page 23

A l a r m

Test

Transmission Device
activated

Bypassed

Transmission Device
bypassed

Signals bypassed

Power

Fault

Fault Transmission
Device

Fault System

Fault Signals

Bypass

Isolate

Maintenance

Switch to day mode

Search Function/

Element

Diagnostics

Configuration

Further functions

Reset

Fire

Control

Fault

Bypass

Status

Function keys

Key switch

Alphanumeric keypad

LED display

4.1

Operating elements

The operating elements include points 1 - 3.

Function keys

To select a function, press the appropriate membrane key.
The following functions can be executed with the function keys:

Display a list of the networked panels and establish a remote
connection with a networked panel (only valid for FPA-5000) or a
remote keypad.

Display the address for technical support, if saved.

Summary of Contents for FPA-1200-MPC-C





































































































Search results

Summary of Contents for FPA-1200-MPC-C

Reviews:

Related manuals for FPA-1200-MPC-C

Brands by name

Popular brands

Bosch FPA-1200-MPC-C, User Manual

Search results

Summary of Contents for FPA-1200-MPC-C

Reviews:

Related manuals for FPA-1200-MPC-C

Brands by name

Popular brands