Bosch FPA-1200-MPC-C User Manual Download Page 70

Page: 70 / 100

en | Maintenance

Panel Controller

2017.09 | 7.0 | F.01U.258.929

User Guide

Bosch Sicherheitssysteme GmbH

Maintenance

This chapter contains information about the following points:
–

Walktest: see Maintenance – walktest, page 73

–

Changing language display, page 70

–

Activate Outputs, page 70

–

Activate Transmission Device, page 71

–

Detector removal, page 71

–

Change device on V.24 Interface, page 71

–

History Log: see Maintenance – history log, page 77

–

Bypassing/Un-bypassing buzzer, page 72

15.1

Menu overview

Maintenance

Walktest

Change language

Activate outputs

Activate transmission device

Remove detector

History log

Change device at V.24
interface

Bypass buzzer

15.2

Changing language display

Notice!

The fastest way to change the language display is via a shortcut; see also Changing language
display, page 31.

There are two ways of selecting a different language display:
–

Using the menu

–

Entering a shortcut; see Changing language display, page 31.

Notice!

After the system starts up following a power cut or battery failure, the default language
defined in the FSP-5000-RPS programming software is set again.

Making a selection via the menu

In the start menu, select

Maintenance

Change language

A list of the languages which can be selected is displayed.

Select the language you require.
The displays are displayed in the selected language.

15.3

Activate Outputs

In the start menu, select

Maintenance

Activate outputs

Various element categories are displayed.

Select a category or

Select by number

and enter the number of the element into the

search screen; see also Search Function/Element, page 29

Select the required list fields. The list fields are marked.

Summary of Contents for FPA-1200-MPC-C





































































































Search results

Summary of Contents for FPA-1200-MPC-C

Reviews:

Related manuals for FPA-1200-MPC-C

Brands by name

Popular brands

Bosch FPA-1200-MPC-C, User Manual

Search results

Summary of Contents for FPA-1200-MPC-C

Reviews:

Related manuals for FPA-1200-MPC-C

Brands by name

Popular brands