background image

4. Download the configuration on the DDU 7. To connect the DDU 7 to Race‐

Con, see chapter ‘

Connecting the unit to RaceCon [

}

 16]

’.

5. Open a measurement sheet by clicking on the desired measurement sheet in

the Project Tree.

6. Drag the ‘grp_adj_channel’ and the ‘input_grp_adj_channel’ to the online

measurement sheet.

7. Press and release the push‐button.
8. The measurement labels indicate the state of the input pin and the state of

the adjustment.

 

Notice

A display alarm can be linked to the trigger channel to indicate
that the trigger has been detected.

 

 

Online calibration of multipoint adjustment
channels

Example: measurement of wheel force

▪ Physical property ‘wheel force’ not directly measureable
▪ Load transfer through suspension kinematics
▪ Physical value at sensor position defined by vehicle
▪ Curve definition by online adjustment at vehicle

 

 

 

 

Force at wheel 

Force at sensor 

1. Create a multipoint adjustment measurement channel. To create a multipoint

channel, see chapter ‘

Configuring a multipoint adjustment [

}

 75]

’.

2. Download the configuration on the DDU 7. To connect the DDU 7 to Race‐

Con, see chapter ‘

Connecting the unit to RaceCon [

}

 16]

’.

3. Click on the desired channel in the DDU 7 Project Tree.
4. Double‐click on a measurement channel in the Data Area to open the online

view.

 

11.5

11 | Online Measurement

 

98 / 160

DDU 7 Manual

Bosch Motorsport

Summary of Contents for DISBLAY DDU 7

































































































































































Reviews: