Bosch DISBLAY DDU 7 Manual Download

Page: 87 / 160

Going online

Click ‘OK to download RaceCon configuration to DDU 7.
The download starts.

A green dot and background at the device in the project view and the DDU 7
Project Tree indicate a successful download and system consistency.

If the system’s configuration in RaceCon has been changed, the dot and back‐
ground becomes yellow and a configuration download is necessary.

Configuration download

1. Right‐click on DDU 7 in the DDU 7 Project Tree.
2. Select ‘Download configuration’.

The configuration download starts.
A Green dot and background indicate a successful download.

11.1.2

11.1.3

Online Measurement | 11

Bosch Motorsport

DDU 7 Manual

87 / 160

Summary of Contents for DISBLAY DDU 7

































































































































































Search results

Summary of Contents for DISBLAY DDU 7

Reviews:

Related manuals for DISBLAY DDU 7

Brands by name

Popular brands

Bosch DISBLAY DDU 7, Manual

Search results

Summary of Contents for DISBLAY DDU 7

Reviews:

Related manuals for DISBLAY DDU 7

Brands by name

Popular brands