manualshive.com logo in svg

Bosch DISBLAY DDU 7, Manual, Page: 54 / 160

Share
Download
Bosch DISBLAY DDU 7 Manual Download Page 54

CAN Bus

DDU 7 has two fully configurable CAN buses.

▪ Baudrate (125 kBaud … 1 MBaud)
▪ 11 Bit or 29 Bit identifiers
▪ Input configuration: Read messages from CAN bus and convert to DDU 7

measurement/display variables. CAN bus supports row counter configura‐
tion.

▪ Output configuration: Write DDU 7 measurement variables to CAN messages,

output frequency and row counter are configurable, CAN gateway function‐
ality (transfer from one bus to the other).

CAN bus trivia

CAN message

▪ 11 Bit (standard) or 29 Bit (extended) identifier
▪ Up to 8 bytes of data payload

CAN bus

▪ Needs termination resistors (120 Ohm) in wiring harness
▪ All devices connected to the bus must use identical data rate
▪ Configuration of bus data rate in ‘Properties’ menu by double click on the

CAN bus in project tree (1 MBaud, 500 kBaud, 250 kBaud, 125 kBaud).

Row counter concept

▪ Re‐use (multiplex) of message identifiers
▪ One byte of message contains row counter
▪ 7 bytes payload remaining
▪ Position of row counter is configurable

9

9.1

9 | CAN Bus

 

54 / 160

DDU 7 Manual

Bosch Motorsport

Summary of Contents for DISBLAY DDU 7

































































































































































Reviews:

No comments