Bosch DISBLAY DDU 7 Manual Download

Page: 30 / 160

A new empty page opens.

Selecting display pages

Click on ‘DDU 7’ in the DDU 7 Project Tree, then on ‘Display’ and double‐click on
the page you want to select (example: ‘New Page’).

In the Main Area, a representation of the DDU 7 opens.

Tabs to switch
between different
items / pages

Configurable
LEDs

Display area

Display element configuration

Numeric display element

Adding a numeric display element to display page

The ‘Large Element’ and the ‘Medium Element’ numeric display elements differ in
element and font size. The element and font size can be changed using the Nu‐
meric Wizard.

Notice

In this view the displayed values are random values and do not
show the real values of the measurement channels.

1. Drag a numeric display element from the Toolbox and drop it on the display

page. A message in the numeric element box shows that it is not linked to a
measurement channel.

8.1.3

8.2

8.2.1

8 | Display Configuration

30 / 160

DDU 7 Manual

Bosch Motorsport

Summary of Contents for DISBLAY DDU 7

































































































































































Search results

Summary of Contents for DISBLAY DDU 7

Reviews:

Related manuals for DISBLAY DDU 7

Brands by name

Popular brands

Bosch DISBLAY DDU 7, Manual

Search results

Summary of Contents for DISBLAY DDU 7

Reviews:

Related manuals for DISBLAY DDU 7

Brands by name

Popular brands