Bosch CLC6001i 25 E Service Manual Download

Page: 62 / 120

6-11

Climate Class 6100i / 6000i / 8100i / 8000i

①

Lift it up

Disassemble the top cover after removing 4 screws of it.

( Left side of top cover )

( Right side of top cover )

②

①

1 Body’s decomposition steps

Disassemble the screw fixing side cover, then disassemble the

side cover.

Disassemble fixing terminal cover and a screw of cord clamp,

then remove them. At last remove cable holder.(4 screws)

Disassemble the screw fixing ring, then take the ring out as

Open the front cabinet axis on the left

a little on the right

②

Open it outward and

lift up a little on the left, then open it.

Disassemble side cover R.(8 screws)

Disassemble side cover L.(6 screws)

Disassemble the front cabinet ass’y.(5 screws in front side,

4 screws in right side.)

[3] OUTDOOR UNIT(CLC8101i 65 HE, CLC8001i 25/35 E)

below picture direction.

Take

out

Summary of Contents for CLC6001i 25 E

























































































































Search results

Summary of Contents for CLC6001i 25 E

Reviews:

Related manuals for CLC6001i 25 E

Brands by name

Popular brands

Bosch CLC6001i 25 E, Service Manual

Search results

Summary of Contents for CLC6001i 25 E

Reviews:

Related manuals for CLC6001i 25 E

Brands by name

Popular brands