Bosch CLC6001i 25 E Service Manual Download

Page: 67 / 120

This document has been published to be used for

after sales service only.

The contents are suject to change without notice.

Parts marked with "

" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the

safety and performance of the set.

PARTS LIST

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the

following information.

1. MODEL NUMBER

2. REF. NO.

3. PART NO.

4. DESCRIPTION.

MODELS

CONTENTS

[1] INDOOR UNIT

(CLC8101i_CLC8001i) ....................

- MODEL: CLC8101i-W 65 HE

CLC8001i-W 25/35 E

..........................................

- MODEL: CLC8101i-W 65 HER/T

CLC8001i-W 35 ER/T

CLC8001i-W 25 ER/T

.........................................

- MODEL: CLC8101i-W 65 HES

CLC8001i-W 25/35 ES

........................................

[2] INDOOR UNIT

(CLC6101i_CLC6001i) ...................

- MODEL: CLC6101i-W 50/65 HE

CLC6001i-W 25/35 E

........................................

[3] OUTDOOR UNIT

(CLC6101i_CLC6001i) ............

- MODEL: CLC6101i 50/65 HE
CLC8001i 25/35 E

............................................

[4] OUTDOOR UNIT

(CLC8101i_CLC8001i) ...........

- MODEL: CLC8101i 65 HE

.............................................

- MODEL: CLC8001i 25 E

CLC8001i 35 E

...............................................

AIR/AIR HEAT PUMP

Climate Class 6100i / 6000i / 8100i / 8000i

INDOOR UNIT OUTDOOR UNIT

CLC6101i-W 50 HE CLC6101i 50 HE

CLC6101i-W 65 HE CLC6101i 65 HE

CLC8101i-W 65 HE(T/S/R) CLC8101i 65 HE

CLC6001i-W 25 E CLC6001i 25 E

CLC6001i-W 35 E CLC6001i 35 E

CLC8001i-W 25 E(T/S/R)

CLC8001i 25 E

CLC8001i-W 35 E(T/S/R)

CLC8001i 35 E

Summary of Contents for CLC6001i 25 E

























































































































Search results

Summary of Contents for CLC6001i 25 E

Reviews:

Related manuals for CLC6001i 25 E

Brands by name

Popular brands

Bosch CLC6001i 25 E, Service Manual

Search results

Summary of Contents for CLC6001i 25 E

Reviews:

Related manuals for CLC6001i 25 E

Brands by name

Popular brands