Bosch CLC6001i 25 E Service Manual Download

Page: 36 / 120

4-16

Climate Class 6100i / 6000i / 8100i / 8000i

Problem

symptom

Outdoor

unit

indica-

tion

(LED1)

Malfunction

No.*

Content of diagnosis

Check point

Action

Main

Sub

Main

Sub

Indoor unit

operates.

Outdoor

unit does

not oper-

ate

temporarily

2-time

Cycle

temperature

Compressor dis-

charge overheat.

1) (Temporary stop for cycle

protection)

Outdoor unit

heat exchanger

overheat.

Indoor unit heat

exchanger over-

heat.

Indoor and

outdoor

units do

not

operate.

IPM high

temperature error

(1)Check the outdoor unit

air outlet for blockage.

(2)Check the outdoor unit

fan for proper rotation.

(3)No abnormality found

in above inspections (1)

and (2).

(1)Ensure unobstructed

air flow from the out

door unit air outlet.

(2)Check the outdoor unit

fan motor.

(3)Replace the outdoor

unit control PWB.

Indoor unit

operates.

Outdoor

unit does

not operate

temporari-

ly.

3-time

Dry operation

Temporary stop

due to dehumidi-

fying operation

1) (Temporary stop for cycle

protection).

Indoor and

outdoor

units do

not

operate.

5-time

Outdoor unit

thermistor

open-circuit

Heat exchanger

thermistor open

circuit error

1) Check connector of out-

door unit thermistor for

secure installation.

2) Measure resistance of

outdoor thermistors.

3) Check the lead wires of

thermistors on the out-

door unit control PWB for

open-circuit.

4) No abnormality found

in above inspections (1)

through (3).

1) Correct the installation.

2) Replace the outdoor

unit thermistor assem-

bly.

3) Replace the outdoor

unit thermistor assem-

bly.

4) Replace the outdoor

unit control PWB as-

sembly.

Outdoor temper-

ature

thermistor open

circuit error

Suction thermis-

tor open circuit

error

2-way valve

thermistor open

circuit error.

Discharge

thermistor open

circuit error

Heat sink ther-

mistor open

circuit error

Indoor and

outdoor

units do

not oper-

ate.

6-time

Outdoor unit

DC Current

DC over current

error

1) Go to “DC Over Current Error (6-0 error)”.

IPM pin level

error

1) Check the IPM is at-

tached correctly to the

outdoor unit IPM PWB.

1) Replace the outdoor

unit PWB.

Summary of Contents for CLC6001i 25 E

























































































































Search results

Summary of Contents for CLC6001i 25 E

Reviews:

Related manuals for CLC6001i 25 E

Brands by name

Popular brands

Bosch CLC6001i 25 E, Service Manual

Search results

Summary of Contents for CLC6001i 25 E

Reviews:

Related manuals for CLC6001i 25 E

Brands by name

Popular brands