Bolide SVR9500H Series User Manual Download

Page: 60 / 261

USER MANUAL

Bitrate

This parameter corresponds to the speed of the data transfer that the DVR will use to

record

video. Recordings that are encoded at higher bitrates will be of better quality.

Audio

Select this option if you want to record audio along with video and have a

microphone

connected to the DVR or use a camera with audio capability.

I Frame Interval:

Using the default number is OK.

ETR:

If ETR option is checked, this channel will be recorded at the maximum frame rate &

bitrate

when an alarm (motion or I/O alarm) triggered in this channel.

5.2.2 Record

This menu allows you to configure the channel recording parameters.

5.2.2.1 Record

Record Switch

: Check to enable recording in this channel.

Stream Mode

: Choose the recording quality. If you choose Dualstream, the system will record

both Mainstream & Substream.

PreRecord

: If this option is enabled, the DVR starts recording a few seconds before an alarm

event occurs. Use this option if your primary recording type is motion or I/O alarm based.

Summary of Contents for SVR9500H Series






































































































































































































































































Search results

Summary of Contents for SVR9500H Series

Reviews:

Related manuals for SVR9500H Series

Brands by name

Popular brands

Bolide SVR9500H Series, User Manual

Search results

Summary of Contents for SVR9500H Series

Reviews:

Related manuals for SVR9500H Series

Brands by name

Popular brands