manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 84

Refueling

Fuel is highly flammable.
Fire at the fuel tank can

result in fire and explosion.
Do not smoke. Never bring
a naked flame near the fuel
tank.

Fuel expands when ex-
posed to heat. When the

tank is overfilled, fuel can es-
cape and get onto the rear
wheel. This results in a dan-
ger of falling.
Do not fill the tank past the
bottom edge of the filler
neck.

Fuel attacks plastic sur-
faces, making them dull

or unsightly.
Wipe spilled fuel off plastic
parts immediately.

Leaded fuel will destroy
the catalytic converter!

Use only unleaded fuel.

Make sure the ground is
level and firm and park the
motorcycle.

Open the protective cap.
Open the fuel tank cap with
the ignition key by turning
counterclockwise.
Fill the tank with fuel of the
quality listed below.

The nominal value
for mileage and

consumption apply for the
recommended fuel type.

Recommended fuel type

Premium grade unleaded
fuel
98 ROZ

Fuel types can be used with
poorer performance and
consumption

Normal unleaded
91 ROZ

Usable fuel quantity
7.1 gal
Reserve fuel quantity
1.1 gal

Close the fuel tank cap with
firm pressure.
Remove the key and close
the protective cap.

5

82

z

Riding

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands