manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 170

E

3

BMW Mo

to

rrad 

Inte

gral ABS

How can the shortest 
braking distance be 
achieved?

During braking the dynamic 
load distribution between the 
front and rear wheel changes. 
The heavier braking is, the 
higher the load on the front 
wheel. The greater the wheel 
load, the more braking force 
can be transferred.
To achieve the shortest possi-
ble braking distance, the front 
brake must be operated 
quickly and with increasing 
force. This optimally utilizes 
the dynamic load increase on 
the front wheel. At the same 
time, the clutch should also be 
disengaged.
With the "forced braking" often 
practiced, during which the 
brake pressure is generated

as quickly as possible and with 
maximum force, the dynamic 
load distribution is unable to 
follow the increase in 
deceleration and the brake 
force cannot be completely 
transferred to the road sur-
face. To prevent locking of 
the front wheel, the ABS must 
intervene and reduce the 
brake pressure, which 
increases the braking 
distance.

What happens when the ABS 
control function fails?

A fault in the BMW Motorrad 
Integral ABS is indicated by a 
corresponding warning in the 
instrument cluster.
If only the ABS control function 
fails, the integral system and 
the brake booster continue to
operate. If these systems also

fail, the residual braking func-
tion is activated. In this case, 
the forces to be applied to the 
brake levers are considerably 
higher and the required lever 
travel increases.
The residual braking function 
is a mechanical function and is 
always available when the 
BMW Motorrad Integral ABS 
fails, regardless of the battery 
charging level. It meets all 
requirements of the worldwide 
legislation on the brake design 
of motor vehicles and enables 
the rider to brake the motor-
cycle. 
When driving with the residual 
braking function, the following 
instructions must be followed:
• Adjust the brake levers to 

the maximum travel

Info_I_ABS_us_xx.fm  Seite 3  Freitag, 22. Juli 2005  10:09 10

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands