manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 126

Always charge a completely
drained battery directly at the
terminals of the disconnected
battery.

Charge the disconnect-
ed battery via the onboard
socket.

The motorcycle's
onboard electronics

know when the battery is fully
charged. The onboard socket
is switched off when this
happens.

Comply with the operating
instructions of the charger.

If you are unable to
charge the battery via

the onboard socket, you
may be using a charger that
is not compatible with your
motorcycle's electronics.
In this case, please charge
the battery directly at the
terminals of the disconnected
battery.

Charging disconnected
battery

Charge the battery using a
suitable charger.
Comply with the operating
instructions of the charger.
Once the battery is fully
charged, disconnect the
charger terminal clips from
the battery terminals.

In the case of longer pe-
riods when the motor-

cycle is not being used, the
battery must be recharged
regularly. See the instruc-
tions for caring for your bat-
tery. Always fully recharge the
battery before returning it to
use.

Removing battery

Make sure the ground is
level and firm and park the
motorcycle.

Removing passenger seat
(

57)

Removing driver's seat
(

57)

Switch off the ignition.

An incorrect disconnec-
tion sequence increase

the risk of short-circuiting.
Always observe the proper
sequence.

Remove the screw

1

.

Remove battery negative
cable

2

first.

7

124

z

Maintenance

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands