manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 53

2

Switch in middle posi-
tion: Heating off.

3

Switch pressed toward
rear: 50% heating ca-
pacity.

4

Switch pressed toward
front: 100% heating ca-
pacity.

Shown in multifunction
display

Switch on driver's or pas-
senger heating.

The following symbols are
shown in dependence on the
selected heating level:

Driver's seat 50% heat-
ing capacity

Driver's seat 100% heat-
ing capacity

Passenger seat 50%
heating capacity

Passenger seat 100%
heating capacity

Clutch

Adjusting clutch lever

The distance between han-
dlebar grip and clutch lever
can be adjusted to any of
three positions.

Adjusting clutch lever

If the position of the
clutch fluid reservoir is

changed, air can enter the
clutch system.
Do not reposition the handle-
bar controls on the handle-

4

51

z

Operation

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands