BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 50

Page: 50 / 171

Cruise control is deactivat-
ed.
Cruise-control indicator light
goes out.
Indicator light in switch re-
mains on.

Resuming former cruis-
ing speed

Push button

in RES direc-

tion.

Opening the throttle
does not deactivate

the cruise-control system. If
you release the twistgrip the
motorcycle will decelerate

only to the cruising speed
saved in memory, even
though you might have
intended slowing to a lower
speed.

Cruise-control indicator
light lights up.

Stored speed is resumed.

Switching off cruise con-
trol

Move switch

to OFF.

The system is deactivated.
Button

is locked.

Emergency ON/OFF
switch

Actuating the emergen-
cy ON/OFF switch while

driving can cause the rear
wheel to lock up, resulting in
a fall.
Do not operate the emergen-
cy ON/OFF switch while rid-
ing.

Operation

Summary of Contents for R 1200 RT 2005












































































































































































Search results

Summary of Contents for R 1200 RT 2005

Reviews:

Brands by name

Popular brands

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Search results

Summary of Contents for R 1200 RT 2005

Reviews:

Brands by name

Popular brands