manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 102

Specified level of engine oil
Oil level visible in sight glass

If the oil level is below the
MIN mark:

Topping up engine oil
(

100)

If the oil level is above the
MAX mark:

Have the oil level corrected
by a specialized workshop,
preferably an authorized
BMW motorcycle retailer.

Topping up engine oil

Both too little and too
much engine oil can lead

to engine damage.
Always make sure that the oil
level is correct.

Wipe the area around the
filler neck clean.
Remove cap of fill location
for engine oil

1

with toolkit.

Add engine oil up to speci-
fied level.
Install cap of fill location for
engine oil

1

with toolkit.

General brake system

Functioning brakes

A properly functioning brake
system is a basic require-
ment for the road safety of
your motorcycle.
Do not ride the motorcycle if
you have any doubts about
the dependability of the brake
system.
In this case, have the brake
system checked by a certified
workshop, preferably by an
authorized BMW motorcycle
retailer.

Incorrect working prac-
tices endanger the relia-

bility of the brakes.
Have all work on the brake
system performed by a certi-
fied workshop, preferably by
an authorized BMW motorcy-
cle retailer.

7

100

z

Maintenance

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands