BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 25

Page: 25 / 171

Warning and indicator
lights

Indicator light, left turn
indicator

Indicator light, high-beam
headlight

Indicator light, neutral

ABS warning light

Indicator light, right turn
indicator

Warning light, general

ABS warning light

In some countries a different
display of the ABS warning
light is possible.

Alternative display of
ABS warning light.

Function indicators

Fuel capacity

The horizontal bars un-
der the gas pump sym-

bol indicated the remaining
fuel quantity.

Gear

Engaged gear is indicat-
ed.

If no gear is engaged, the
gear indicator displays 0; the
'neutral' indicator light also
lights up.

Engine temperature

The lateral bars under
the temperature symbol

show the engine temperature
level.

General warning indi-
cators

Display

General warnings are dis-
played by means of texts and
symbols in the multifunction
display. In some cases, an
additional general warning
light lights up red or yellow.
A number of warnings may be
issued simultaneously.

Status indicators

Indicator light, cruise

control

Summary of Contents for R 1200 RT 2005












































































































































































Search results

Summary of Contents for R 1200 RT 2005

Reviews:

Brands by name

Popular brands

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Search results

Summary of Contents for R 1200 RT 2005

Reviews:

Brands by name

Popular brands