manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 60

Raise the front seat at the
rear.

with OE Seat heating:

Disconnect connector

2

.

Lift the seat up to remove.

Adjusting driver's seat

The front seat can be raised
or lowered to either of two
positions.

Adjusting driver's seat

Make sure the ground is
level and firm and park the
motorcycle.
Removing passenger seat
(

57)

Removing driver's seat
(

57)

Take out seat supporting
rod

1

and install in respec-

tive other holder.

Installing driver's seat
(

58)

Installing passenger seat
(

59)

Installing driver's seat

If too much pressure is
applied in the forward

direction, there is a danger
that the motorcycle will be
pushed off its stand.
Make sure that the motorcy-
cle is steady on its stand.

with OE Seat heating:

Close connector

2

.

4

58

z

Operation

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands