manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 44

Tripmeter and onboard
computer

OE

On motorcycles with an on-
board computer, the tripmeter
reading is displayed alternate-
ly with the odometer reading.

Resetting tripmeter

Switch on the ignition.

Select desired tripmeter.
Press tripmeter button

1

and hold it down for longer
than 2 seconds.
The tripmeter is reset to ze-
ro.

Clock

Setting clock

Attempting to set the
clock while riding the

motorcycle can lead to ac-
cidents.
Adjust the clock only when
the motorcycle is stationary.

Switch on the ignition.

Press button

1

for longer

than 2 seconds.
Hours reading

2

starts to

flash.
Briefly press button

1

.

The hour increments by one
each time you press the
button.
Press button

1

for longer

than 2 seconds.
Minutes reading

3

starts to

flash.
Briefly press button

1

.

The minute increments by
one each time you press
the button.
Press button

1

for longer

than 2 seconds.
Setting confirmed.

Multifunction display

Display dimming

The brightness of the backlit
multifunction display is vari-
able.

4

42

z

Operation

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands