manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Rider'S Manual

Share
Download
BMW Motorrad R 1200 RT 2005 Rider'S Manual Download Page 29

Engine oil pressure insuffi-
cient

General warning light
lights up red.

Engine oil pressure sym-
bol is displayed.

The oil pressure in the lubri-
cating oil circuit is too low.

The warning on insuffi-
cient engine oil pressure

is no substitute for the func-
tion of an oil-level indicator.
The correct engine oil level
can only be checked at the oil
sight glass.

The cause of the warning on
insufficient engine oil pres-
sure can be an insufficient
engine oil level.

Checking engine oil level
(

99)

Topping up engine oil
(

100)

If the warning on insufficient
engine oil pressure appears
despite a correct engine oil
level:

In addition to an insuf-
ficient engine oil level,

other problems in the engine
can lead to the warning on in-
sufficient engine oil pressure.
Continuing to ride in these
cases can cause engine dam-
age.
If this warning appears de-
spite a correct engine oil lev-
el: Do not continue driving.

Do not continue driving.
Have the fault rectified as
soon as possible by a spe-
cialized workshop, prefer-
ably an authorized BMW
motorcycle retailer.

Battery charge current in-
sufficient

General warning light
lights up red.

Battery charge current
symbol is displayed.

A discharged battery can
result in the engine cut-

ting out unexpectedly, caus-
ing a hazardous situation.
Have faults eliminated as
soon as possible.

If the battery is no longer
charged, continued

driving can lead to deep
discharging, and therefore to
the destruction of the battery.
If possible, do not continue
driving.

The battery is not being
charged.

Continued driving is possi-
ble until the battery is dis-
charged. However, the en-

3

27

z

Status indicators

Summary of Contents for R 1200 RT 2005












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands