Blackmagicdesign ATEM Camera Converter Installation And Operation Manual Download Page 72 | Manualshive

Page: 72 / 136

background image

Operating your ATEM Switcher

72

DVE transition parameters

DVE Rate

The duration of the DVE transition in seconds and frames. Rotate the DVE rate
knob to adjust the DVE transition rate. The new rate is immediately displayed in
the transition rate window in the transition control block.

Normal

The normal direction applies the DVE effect on program, revealing the preview
channel.

Reverse

Reverse changes the direction so that the DVE effect is applied on the preview
channel. In the case of reverse, program is covered by a DVE effect with the
preview video.

FlipFlop

When FlipFlop mode is toggled on, the transition changes between normal and
reverse every time the transition is executed.

DVE key parameters

Enable

Enables/disables the DVE key. The DVE key is enabled when the button is
illuminated.

PreMult

Selects the DVE key as a pre-multiplied key.

Clip

The clip level adjusts the threshold at which the key cuts its hole. Decreasing the
clip level reveals more of the background. If the background video is completely
black then the clip value is too low.

Gain

The gain adjustment electronically modifies the angle between on and off
thereby softening the edges of the key. Adjust the gain value until the edge
softness is desirable but the background video luminance (brightness) is not
affected.

Inverse

When the key is not pre-multiplied, inverts the key signal.

Sharing DVE resources

ATEM features a DVE channel which can be used to perform DVE transitions or used in an upstream keyer.
The ATEM Television Studio and Production Studio 4K do not have any DVE channels available. When
you select a DVE transition, if the DVE is used elsewhere in the system, the DVE transition type will not be
available and, on the broadcast panel, a DVE unavailable message will be displayed. In order to use the DVE
transition you must free the DVE from where it is currently used. Verify that the upstream keys currently on
program or preview are not DVE keys and do not have fly key enabled. To free DVE from the upstream keyer,
change the key type to anything other than DVE or disable fly key. The DVE will be released and therefore
available for use as a DVE transition.

«
...
70
71
72
73
74
...
»

Summary of Contents for ATEM Camera Converter









































































































































Reviews:

No comments

Related manuals for ATEM Camera Converter

Brand: Ikelite Pages: 2

Brand: Kramer Pages: 15

Brand: PEAK COMMUNICATIONS Pages: 18

Brand: Optical Systems Pages: 2

Brand: Vacon Pages: 12

Hubner Berlin POG 86

Brand: Baumer Pages: 36

Brand: Interlogix Pages: 20

Brand: CEL-MAR Pages: 16

Brand: Enerdrive Pages: 48

Brand: Visual Circuits Pages: 75

Brand: Pulse-Eight Pages: 2

Brand: Audio Note Pages: 79

Brand: Katranji Pages: 5

Brand: austriamicrosystems Pages: 12

Brand: SMA Pages: 222

Brand: coov Pages: 12

Brand: Toxic Pages: 2

Brand: Hegel Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands