5
ENGLISH
(Original instructions)
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool, along with the
date code
:
:
Warning!
To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust extraction connector.
3. Base
4. Tip holder
5. Sanding base tip
6. Screw
7. Diamond shaped tip
8. Sanding sheet
In addition, this tool is supplied with some or all of the
following accessories:
Accessory
Recommended application and use
Coarse grit
sandpaper
Fast paint, varnish and rust removal
Medium grit
sandpaper
Paint, varnish and rust removal
Fine grit
sandpaper
Surface blending and finishing
Assembly
Warning!
Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A & B)
u
Detach the two diamond-shaped tips (7) from the
sanding sheet (8).
u
Hold the tool with the sanding base facing upwards.
u
Place the sanding sheet (8) onto the sanding base,
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (10) can be reversed and replaced
when worn.
u
When the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
u
When the whole tip is worn, remove it from the sanding
base and fit a new tip.
u
The polishing foam and pads (14) can be fitted the same
way as the sanding sheets.
Tip of the sanding base (fig. D)
When the sanding base tip (5) or tip holder (4) is worn, it can
be reversed or replaced. Spare parts are available from your
BLACK+DECKER dealer.
u
Remove the screw (6).
u
Reverse or replace the worn part.
u
Fit and tighten the screw.
Use
Warning!
Let the tool work at its own pace. Do not overload.
Warning!
Do not cover the ventilation slots when using the
tool. Hold the tool as shown in fig. H. Make sure that the
sanding base is flat on the workpiece.
Connecting a vacuum cleaner (fig. E)
The tool has an adaptor to connect it to a vacuum cleaner
when sanding wood. To connect the tool to a vacuum cleaner,
proceed as follows:
Warning!
Make sure that the tool is switched off and
unplugged.
u
Fit the dust extraction connector (2) onto the adapter at
the back of the tool.
u
Connect the hose of a suitable vacuum cleaner to the
connector.
Switching on and off (fig. F)
Warning!
Before connecting the tool to the power supply,
make sure it is switched off.
u
To switch the tool on, press the part of the on/off switch (1)
marked 'I'.
u
To switch the tool off, press the part of the on/off switch (1)
marked '0'.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Summary of Contents for BDM55
