Black Box LPB201A User Manual Download Page 97 | Manualshive

Page: 97 / 182

background image

4.22 Firmware Upgrade

Software upgrade tool is used to help upgrade the software function in order to fix or improve the function.
The switch provides a TFTP client for software upgrade. This can be done through Ethernet.

The switch supports TFTP upgrade tool for upgrading software. If you assure to upgrade software to a newer
version one, you must follow two procedures:

1.

Specifying the IP address where TFTP server locates. In this field, the IP address of your TFTP server
should be filled in.

2.

Specifying what the filename and where the file is. You must specify full path and filename.

Then, press

Upgrade

button if your download is not successful, the switch will also be back to “Software

Upgrade”, and it will not upgrade the software as well.

When download is completed, the switch starts upgrading software. A reboot message will be prompted after
completing upgrading software. At this time, you must reboot the switch to have new software worked.

NOTE

Software upgrade is hazardous if power is off. You must do it carefully.

Table 4-65. Firmware Upgrade screen options.

Parameter Description

TFTP Server

A TFTP server stored the image file you want to upgrade.

Path and Filename

File path and filename stored the image file you want to upgrade.

4.23 Reboot

We offer you many ways to reboot the switch, including power up, hardware reset and software reset. You can
press the RESET button in the front panel to reset the switch. After upgrading software, changing IP
configuration or changing VLAN mode configuration, then you must reboot to have the new configuration
taken effect. Here we are discussing is software reset for the reboot in the main menu.

Reboot the switch. Reboot takes the same effect as the RESET button on the front panel of the switch. It will
take around thirty (30) seconds to complete the system boot.

Table 4-66. Reboot screen options.

Parameter Description

Save and Reboot

Save the current settings as start configuration before rebooting
the switch.

Reboot

Reboot the system directly.

24-Port 10/100BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports

95

«
...
95
96
97
98
99
...
»

Summary of Contents for LPB201A























































































































































































Reviews:

No comments

Related manuals for LPB201A

Brand: l-com Pages: 12

Brand: 3Com Pages: 1133

Brand: Hall Technologies Pages: 35

Brand: Mach Power Pages: 12

Brand: Metrix Pages: 12

Brand: Accton Technology Pages: 10

Brand: Lancom Pages: 23

Brand: H3C Pages: 26

Brand: Pakedge Pages: 12

Brand: ADS Technologies Pages: 2

Brand: Lantech Pages: 29

Brand: TRENDnet Pages: 2

Brand: Guntermann & Drunck Pages: 8

Brand: A-Neuvideo Pages: 9

Brand: Lindy Pages: 7

Brand: QNAP Pages: 30

Brand: AAVARA Pages: 8

Brand: QNAP Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands