Black Box LPB201A User Manual Download Page 114

Page: 114 / 182

show

Syntax: show

Description: Shows a system account, including account name and identity.

Argument: None

Possible value: None

Example:

Giga Switch(account)# show
Account Name Identity
--------------------------------

admin Administrator
guest guest

alarm

<<email>>

del mail-address

Syntax: del mail-address <#>

Description: Removes the email address configuration.

Argument: <#>: email address number, range of 1 to 6

Possible value: <#>: 1 to 6

Example:

Giga Switch(alarm-email)# del mail-address 2

del server-user

yntax: del server-user

Description: Removes the server, user account, and password configuration.

Argument: None

Possible value: None

Example:

Giga Switch(alarm-email)# del server-user

CHAPTER 5: CLI Management

112

Summary of Contents for LPB201A






















































































































































































Search results

Summary of Contents for LPB201A

Reviews:

Related manuals for LPB201A

Brands by name

Popular brands

Black Box LPB201A, User Manual

Search results

Summary of Contents for LPB201A

Reviews:

Related manuals for LPB201A

Brands by name

Popular brands