Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 96

Page: 96 / 177

Maintenance

5-48

Maintenance
Quantum Flex

Air Operating Instructions and Parts List

Manual No. 107193
November 1, 2018

Seal Plate Maintenance

Required Tools for Seal Plate Maintenance

1 – Small flat head screwdriver

Replace Seal

Step 1: Remove Seal



Use a small flat head screwdriver to pry the seal out of the seal plate.

Step 2: Install Seal



Apply a small amount of Max-Z-Lube to ID of the seal plate.

NOTE:

Use only Max-Z-Lube high performance lubricant.



Press the seal into the seal plate. The lip of the seal should curl into the seal plate.

Seal Plate

Seal

Screwdriver

Lip

Seal

Lubricate I.D.

Seal

Seal Plate

COMPANY

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Search results

Summary of Contents for Quantum Flex Air 1000

Reviews:

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 96 / 177

Search results

Summary of Contents for Quantum Flex Air 1000

Reviews: