Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 94

Page: 94 / 177

Maintenance

5-46

Maintenance
Quantum Flex

Air Operating Instructions and Parts List

Manual No. 107193
November 1, 2018

Assembly of Power Unit

(Continued)

Step 5: Install Muffler

Slide the muffler into the power unit.

Step 6: Install Retainer



Screw the retainer firmly into the power unit, using the supplied spanner wrench. The
retainer is a left-hand thread, and must be turned to the left (counter clockwise), to
tighten.

NOTE: Recommended torque of 25-30 lb-in (2.8-3.4 N-m)

IMPORTANT: Be careful not to cross thread the retainer.
This will cause poor motor performance.

Muffler

Muffler Installed

Retainer

Spanner Wrench

COMPANY

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Search results

Summary of Contents for Quantum Flex Air 1000

Reviews:

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 94 / 177

Search results

Summary of Contents for Quantum Flex Air 1000

Reviews: