manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 116 / 177

Share
Download
Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 116

 

 Cleaning

 

 

6-2 

 Cleaning

 

 

Quantum Flex

®

 Air Operating Instructions and Parts List 

Manual No. 107193   
November 1, 2018 

 

 Periodic Cleaning During Use 

 

Light rinsing during operation is recommended. 
 
Thorough rinsing at each break is highly recommended to improve tool performance. 

 
 

Cleaning after Daily Use 

 

If handpiece is removed from hose assembly, install cap to prevent water and debris from 
entering the motor during cleaning. 
 
Fully disassemble the Quantum Flex

®

 Air Trimmer head assembly and clean each part 

thoroughly with a brush and cleaner.  For best results, clean the Quantum Flex

®

 Air Trimmer 

with Bettcher

®

 

E

XTRA

  

Heavy Duty Cleaner, diluted according to the directions on the 

container.

  

After cleaning, rinse each part thoroughly with water and dry.  Assemble the head 

assembly per instructions in Section 5.

 

 

 

Cleaning Solutions 

 

Avoid the use of aggressive cleaning products and all cleaning products containing NaOH 
(sodium hydroxide) as they will damage the handpiece. 

 

 

 
 
 
 
 
 
 
 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Reviews:

No comments