manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 47 / 177

Share
Download
Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 47

 Instructions for Operation 

 

 

Manual No. 107193  
November 1, 2018 

 Instructions for Operation  
 Quantum Flex

®

 Air Operating Instructions and Parts List 

4-25 

 

Blade Changing 

– Large Tools 

 

 

Sharp blades may cause cut injury! 
 
For proper protection of hands, a protective glove 
should be used when operating this equipment and 
during the handling of blades.   
 
Always disconnect the tool from the air supply prior 
to servicing. 

 

Blade Removal - Large Tools 
Models: 750, 850, 1000, 1300, 1400, 1500, 1850, 1880

 

 

Hold the tool in your hand. 

 

Loosen only the left cover retaining screw 
(Item #1). 

 

With a screwdriver held in the opposite hand, 
insert the screwdriver in the housing slot 
(Item #2). Using the frame as the support 
point (Item #3), spread open the housing. The 
blade should fall out.

 

 

NOTE: Some tools have 2 slots in the housing. 
NOTE:

 

A slight tension on the left cover screw will 

allow the blade housing to stay open on its own. 

 

Blade Installation - Large Tools 
Models: 750, 850, 1000, 1300, 1400, 1500, 
1850, 1880

 

 

Turn the tool over so the blade side is up.

 

 

 

Spread open the blade housing with a screwdriver.

 

 

NOTE:

 

A slight tension on the left cover screw will allow the blade housing to stay open on its 

own. 

 

Insert a new blade in the housing. 

 

Loosen the left cover retaining screw so the housing will close. 

 

Adjust the housing for proper running clearance. The blade should turn freely with a 
slight side-to-side motion. This leaves room for the grease. 

WARNING! 

Make certain that the blade is free to rotate in the housing. If the blade does not 

turn freely, it may cause the tool to rotate in the hand. 

 

Tighten the left cover screw to 35 in-lb. (4 N-m). Use of the Bettcher torque wrench kit is 
recommended. 

 

Re-check the running clearance. 

WARNING

 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Reviews:

No comments