manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 61 / 177

Share
Download
Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 61

 

Maintenance  

 

Manual No. 107193 
November 1, 2018 

 Maintenance  
 Quantum Flex

® 

Air Operating Instructions and Parts List 

5-13 

 

Daily Inspection and Maintenance of Handpiece 

(Continued) 

 

Blade Housing Wear 

 

Small Tool Models: 350, 360, 440, 500, 505, 564, 620, 625 

 

Inspect the inner diameter of the housing for wear  

 

With a new blade installed in the housing on the tool carefully check for movement of the 
blade in the housing from side to side and up and down. 

 

NOTICE:

 

If there is excess movement in the blade from side-to-side and/or up and 

down, the housing is NOT acceptable and needs replaced. 

 

Large Tool Models: 750, 850, 1000, 1300, 1400, 1500, 1850, 1880 

 

Inspect the inner diameter of the housing for wear.  

 

When holding the housing with a new blade installed, if the split in the housing touches 
the other side, and the blade is still loose, the housing needs to be replaced. If a gap is 
seen, the housing is acceptable. 

 

 

 

Pinion Gear 

 

Check for worn or chipped teeth. Worn out teeth are indicated by rounded off and pointed 
tops on the teeth. 

 

Bearing 

 

Install a new pinion and move the pinion side to side. 

 

If the bearing feels egg-shaped, it should be replaced. 

 

The bearing should be replaced at 500 hours of use or sooner. 

 
 
 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Reviews:

No comments