manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 20 / 177

Share
Download
Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 20

 

 Unpacking and Installation 

 

3-4 

 Unpacking and Installation  
 Quantum Flex

®

 Air Operating Instructions and Parts List 

Manual No. 107193   
November 1, 2018 

 

Installation 

 

The workstation for each operator should be designed so that the operator's movements in 
performing the job are natural and easy.  A sideways sweeping motion with the Quantum Flex

®

 

Air Trimmer is preferable to a reaching motion.  Long reaching motions and high muscle strain 
should be avoided if possible.  Also, a proper working height is needed to avoid excessive 
shoulder and back exertion.  

 
 

Air Supply 
 

A clean, dry, lubricated air supply is critical to proper operation.  The filter, regulator and 
lubricator (FRL) unit, furnished with your complete Quantum Flex

®

 Air, should be mounted 

horizontally at the air supply outlet and in such a position as to be easily reached for draining the 
filter bowl and refilling the lubricator.  The filter bowl should be drained, and the lubricator 
refilled, daily. 
 

IMPORTANT

:

  

Be sure the air supply is a constant 90 pounds per square inch (6.2 bar) and the 

volume is a minimum of 14 cubic feet per minute (396 liters per minute) per unit.

 

 

 

Supply Line

:

  

 

 

 

Use a 2 inch to 6 inch (5 cm to 15 cm) pipe for the air supply. 

 

All air outlet drops should be connected to the top of the main air supply line to 
minimize the possibility of moisture and dirt reaching the motor. 

 

Drops should be at least: 

 

¾ inch (2 cm) pipe for one (1) tool. 

 

1 inch (2.54 cm) pipe for two (2) tools.

 

 

1 ¼ inch (3.18 cm) pipe for three (3) tools. 

 

A FRL should be used for each tool.  Do not run multiple tools off of a single 
FRL. 

 

All air outlets should be located close enough to the operator’s work station so that 
additional hose is not required. 

 
 
 
 
 
 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Reviews:

No comments