manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Operating Instructions & Parts List Manual, Page: 102 / 177

Share
Download
Bettcher Quantum Flex Air 1000 Operating Instructions & Parts List Manual Download Page 102

 

 Maintenance

 

 

5-54 

Maintenance 
Quantum Flex

®

 Air Operating Instructions and Parts List 

Manual No. 107193  
November 1, 2018 

 

Inspection and Maintenance of Air Motor 

(

Continued

) 

 
 

Rotor 

 

Inspect the gear teeth for cracked or broken teeth and replace 
the rotor if damaged. 

 

Inspect the gear teeth for excessive wear.  If the gear  
teeth are worn to a sharp point, replace the rotor. 

 

Clean and dry the part thoroughly. 

 
 

Spacer 

 

Inspect the spacer for nicks or cracks.  Replace if damaged. 

 

Clean and dry the part thoroughly. 

 
 

Lower Bearing Plate 

 

Inspect the I.D. and O.D. for nicks, dents, or wear.  Replace the lower bearing plate if 
damaged. 

 

Inspect the alignment pin to be certain it is not bent.  Replace the lower bearing plate if 
damaged. 

 

Clean and dry the part thoroughly. 

 
 
 
 
 
 

 

Gear
Teeth

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex Air 1000


















































































































































































Reviews:

No comments