BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 58

Page: 58 / 118

Maintenance

5-20

Maintenance

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

™

Trimmer

January 1, 2018

MAINTENANCE - WHIZARD

FLEXSHAFT AND CASING

ASSEMBLY (CONTINUED)

Replacement of Split Bearing (#3)

•

Remove the driver assembly.

Refer to Section 5, Removal of the driver assembly

•

Insert a small screwdriver into the split in the bearing.

•

Spread the bearing and slide over the shoulder on the driver.

•

Clean the surface of the coupling and apply Whizard

Special Grease.

•

Hold the bearing with the inside cone facing the end of the coupling.

•

Push the bearing on until it snaps into position.

•

Install the driver assembly.

Refer to Section 5, Installation of the Driver Assembly

Summary of Contents for Quantum Flex 1000























































































































Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List

Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands